This product is a single component, the main component is a-cyanoacrylate, 100% pure reactive monomer, it cures instantly when exposed to moisture in the air, and the bonding takes only a few seconds to a few minutes (depending on the material to be bonded or the ambient temperature) different). It’s no need to heat, easy to use, high bonding strength, and excellent flexibility. It’s suitable for self-adhesive and mutual adhesion of rubber, plastic, glass, porcelain, metal, etc., with good temperature resistance, water resistance and oil resistance.
Product Description
This product is a single component, the main component is a-cyanoacrylate, 100% pure reactive monomer, it cures instantly when exposed to moisture in the air, and the bonding takes only a few seconds to a few minutes (depending on the material to be bonded or the ambient temperature) different). It’s no need to heat, easy to use, high bonding strength, and excellent flexibility. It’s suitable for self-adhesive and mutual adhesion of rubber, plastic, glass, porcelain, metal, etc., with good temperature resistance, water resistance and oil resistance.
Product Usage
|
HY401 |
General purpose, medium viscosity, used for inert surfaces, bonding acidic, porous and absorbent materials. |
|
HY406 |
Low viscosity, used for bonding rubber, plastic and other materials. |
|
HY460 |
Low whitening, used for bonding electronic components with low whitening requirements. |
|
HY495 |
General purpose, low to medium viscosity. Used for bonding rubber, metal and plastic parts. |
|
HY496 |
Medium viscosity. Used for bonding metal and other materials. |
Product Performance
|
Model |
Color |
Curing Speed (25℃) |
Viscosity (mPa•S) |
Filling gap (mm) |
Shear strength (MPa) |
Working temperature (℃) |
|
|
Position |
Fully cured |
||||||
|
HY401 |
Transparence |
20s |
18h |
30~100 |
≤0.10 |
≥10 |
-60~90 |
|
HY406 |
Transparence |
15s |
18h |
5~40 |
≤0.10 |
≥10 |
-60~90 |
|
HY460 |
Transparence |
40s |
18h |
100~300 |
≤0.15 |
≥10 |
-60~90 |
|
HY495 |
Transparence |
20s |
18h |
50~150 |
≤0.15 |
≥10 |
-60~90 |
|
HY496 |
Transparence |
40s |
18h |
80~200 |
≤0.15 |
≥10 |
-60~90 |
Instructions
1. The surface of the adhered must be dry and clean.
2. Spread the glue on the surface of the adhered, leave it in the air for 3 to 5 seconds, and quickly locate and bond.
It will stick firmly after a few seconds or minutes, and reach its highest strength after 24 hours at room temperature.
3. The amount of glue should not be too much. Generally, the amount of glue applied is 4~6mg/cm2.
Matters Needing Attention
1. This product has no organic solvents, and it solidifies instantly when exposed to moisture in the air. Therefore, you should be especially careful when using it to avoid contact with skin and eyes. If it comes in contact with the skin, it can be soaked in acetone and warm water to wash it away; if it gets into the eyes, it must be rinsed immediately with plenty of water and seek medical attention immediately; if it is swallowed, it should be treated immediately by a doctor. Keep out of reach of children, and close the bottle tightly after use.
2. Store in a low temperature (refrigerator) and dry place, with a shelf life of 6 months.
Packing Specification:
20g/bottle, 10 bottles/box, 150bottles/carton
Helen